Powerfold Mirrors With Puddle Lights Retro-fit

The Ford Mondeo hit our roads in 1993, and has consistently been a sales success. Now on its 4th incarnation, it remains a drivers favourite.
For more information, visit the Ford Mondeo forum on TalkFord.com, the definitive resource site covering all Fords from the present day to the 1970's.

---

Overview Guide
Ford Model:	Mondeo
Petrol/Diesel:	Both
Estimated Cost:	£100
Difficulty?	Easy+
How long does this take?	2-3 Hours

Required parts

Facelift

• Mirrors with powerfold & puddle lights.
• Powerfold relay.
• Adjustment switch with powerfold position.

Pre-facelift

As above plus:

• Both front door wiring looms from a facelift mondeo.
• Interior front door plug from a scrapped mondeo as 4 pins from inside the door plug are needed for wiring the puddle lights.

Check below the glovebox fusebox for the brown relay holder. If no brown relay holder is in place then you will need the following too:

• Brown relay holder with wires.
• Fusebox plug & wiring.
• An additional 5 wires & connectors for the door plug.

Fitting

Facelift

1. Remove door card
2. Remove old mirror switch from wiring & plastic surround
3. Refit new switch to plastic cover & plug into the door loom
4. Unplug mirror wiring
5. Remove 3 Torx screws for the mirror (remember to support the mirror on the outside when removing the last screw or risk seven years' bad luck)
6. Fit new mirror unit
7. Refit door card
8. Repeat for the other door
9. Remove glovebox
10. Insert the relay
11. Refit the glovebox

Pre-facelift

1. Remove door card
2. Partially remove the foam weather seal
3. Uncouple door loom from car seperating it from the door by turning it.
4. Uncouple the plugs to the door lock mechanism & window motor.
5. Remove wiring from the door, the rubber seals just pull/push through. Remembering its layout to aid refitting.
6. Refit facelift door loom into the door
7. Plug window motor & door lock unit back in
8. Refit (re-seal if required) the inner weather seal
9. Remove old mirror switch from wiring & plastic surround
10. Fit new switch to plastic cover & plug into the door loom
11. Unplug mirror wiring
12. Remove 3 Torx screws for the mirror (remember to support the mirror on the outside when removing the last screw or risk seven years' bad luck)
13. Fit new mirror unit and plug in the connector.
14. Refit door card
15. Repeat for the other door
16. Remove glovebox
17. Insert the relay
18. Refit the glovebox
19. Add puddle light wiring to the interior of the door plug in the pin locations found below.

If you need to wire in the powerfold relay holder then you will need the following info:

Connector locations

C54 = drivers side upper top door plug.
C52 = passenger side door plug.
C506 = on the rear of the fusebox, top plug nearest the door on the back.

Powerfold relay holder

• Pin 1 - C54 pin 6 & C52 pin 10 (powerfold)
• Pin 2 - C54 pin 10 (switch)
• Pin 3 - C54 pin 7 & C52 pin 1 (powerfold)
• Pin 4 - C506 pin 12 (power feed)
• Pin 5 - ground

Puddle light wiring

Feeds taken from the front footwell lights are easiest, to:

• Driver's side = C54 pin 12 & pin 13
• Passenger side = C52 pin 6 & pin 7

Wiring Diagrams

Powerfold Wiring

Powerfold Switch

Puddle Light Wiring