Registrations
We now manually approve all new user accounts due to a large influx of spam bots. Accounts are normally approved within 48 hours.
If you need any help with using this Wiki, please ask here: TalkFord.com Wiki Submission Forum
Difference between revisions of "Estate Roof Bars Removal"
Compuwiz uk (Talk | contribs) (→Method) |
Compuwiz uk (Talk | contribs) (→Method) |
||
| Line 40: | Line 40: | ||
remove the cap on the b-pillar trim & remove the philips head screw found under there & remove the upper b-pillar trim. | remove the cap on the b-pillar trim & remove the philips head screw found under there & remove the upper b-pillar trim. | ||
| − | |||
| − | |||
[[Image:No5.jpg]] | [[Image:No5.jpg]] | ||
[[Image:No6.jpg]] | [[Image:No6.jpg]] | ||
| + | |||
| + | [[Image:No7.jpg]] | ||
carefully fold back the headlining avoiding creasing the headlining. | carefully fold back the headlining avoiding creasing the headlining. | ||
| Line 53: | Line 53: | ||
undo the 2 T30 torx screws holding the curtain airbag inplace. | undo the 2 T30 torx screws holding the curtain airbag inplace. | ||
| − | [[Image: | + | [[Image:No8.jpg]] |
carefully move the airbag inwards a little ( it wont need moving far & wont really move far as its still attached to the car via various other fixing points ) | carefully move the airbag inwards a little ( it wont need moving far & wont really move far as its still attached to the car via various other fixing points ) | ||
| Line 59: | Line 59: | ||
with the airbag moved out far enough then you can access the 2 bolts with the 10mm socket on the extension bar. | with the airbag moved out far enough then you can access the 2 bolts with the 10mm socket on the extension bar. | ||
| − | [[Image: | + | [[Image:No9.jpg]] |
with these 2 bolts undone the front of the bar is undone. | with these 2 bolts undone the front of the bar is undone. | ||
| Line 75: | Line 75: | ||
remove the 2 plastic pushpegs in the boot space lining. | remove the 2 plastic pushpegs in the boot space lining. | ||
| − | [[Image: | + | [[Image:No10.jpg]] |
remove the d-pillar trims by removing the philips screw found in the boot cover retaining section & then giving the trim a tug from the top to release the clips left holding it inplace ) | remove the d-pillar trims by removing the philips screw found in the boot cover retaining section & then giving the trim a tug from the top to release the clips left holding it inplace ) | ||
| − | [[Image: | + | [[Image:No11.jpg]] |
pull the roof lining down suitably without creasing it. | pull the roof lining down suitably without creasing it. | ||
| Line 85: | Line 85: | ||
using the 10mm socket undo the bolts holding the roof bars inplace ( one is hidden out of the way right inside the bodywork, the other is up near the back end of the curtain airbag ) | using the 10mm socket undo the bolts holding the roof bars inplace ( one is hidden out of the way right inside the bodywork, the other is up near the back end of the curtain airbag ) | ||
| − | [[Image: | + | [[Image:No12.jpg]] |
once this is done the roof bars should be undone from the car & will just require careful lifting off the roof ( the studs the bols fasten onto are pretty long so ithey will need rasing a fair wat before they are fully out - also watch the paintwork too when doing this ) | once this is done the roof bars should be undone from the car & will just require careful lifting off the roof ( the studs the bols fasten onto are pretty long so ithey will need rasing a fair wat before they are fully out - also watch the paintwork too when doing this ) | ||
Revision as of 05:34, 12 October 2008
Mk3 Estate Roof Bar Removal
should you need to remove the mk3 roof bars then the following may be of help.
( this guide is just a rough guide at present & will be updated with better info & piccies later )
Tools Required
10mm Socket & wrench/spanner.
Extension bar for socket.
Torx bits ( T20 - for the in cabin items, T30 - for the curtain airbag screws ).
Philips/cross head screwdriver.
Small Flat Screwdriver.
Method
Front of the bars
undo the 2 T20 torx screws holding the sunvisor to the car & remove the visor.
using the flat screwdriver unclip the cover on the second sunvisor clip & then undo the T20 torx screw under the cover.
repeat the last step for the 2 T20 torx screws holding the grab handle above the door.
remove the a-pillar trim by giving it a tug at the top.
remove the cap on the b-pillar trim & remove the philips head screw found under there & remove the upper b-pillar trim.
carefully fold back the headlining avoiding creasing the headlining.
( there may now be access to both bolts with the use of a spanner but if not the following will need to be done )
undo the 2 T30 torx screws holding the curtain airbag inplace.
carefully move the airbag inwards a little ( it wont need moving far & wont really move far as its still attached to the car via various other fixing points )
with the airbag moved out far enough then you can access the 2 bolts with the 10mm socket on the extension bar.
with these 2 bolts undone the front of the bar is undone.
Repeat on the other side of the car.
Rear Of The Bars
the rears are a little easier.
remove the 2 plastic pushpegs in the boot space lining.
remove the d-pillar trims by removing the philips screw found in the boot cover retaining section & then giving the trim a tug from the top to release the clips left holding it inplace )
pull the roof lining down suitably without creasing it.
using the 10mm socket undo the bolts holding the roof bars inplace ( one is hidden out of the way right inside the bodywork, the other is up near the back end of the curtain airbag )
once this is done the roof bars should be undone from the car & will just require careful lifting off the roof ( the studs the bols fasten onto are pretty long so ithey will need rasing a fair wat before they are fully out - also watch the paintwork too when doing this )
refit in reverse order.
Submitted By Compuwiz_uk
Your Privacy Choices