Registrations
We now manually approve all new user accounts due to a large influx of spam bots. Accounts are normally approved within 48 hours.
If you need any help with using this Wiki, please ask here: TalkFord.com Wiki Submission Forum
Difference between revisions of "Door Cards - Removal"
From www.FordWiki.co.uk
| Line 3: | Line 3: | ||
* Sharp knife | * Sharp knife | ||
* Wide flat-blade screwdriver or similar tool | * Wide flat-blade screwdriver or similar tool | ||
| − | * Medium-sized Phillips-head screwdriver (cross-head, | + | * Medium-sized Phillips-head screwdriver (cross-head, No 2 size) |
| − | * Torx T25 driver | + | * Torx T27 driver, although most people may only have a T25 driver, which will work, but with a lose fit. |
== Method == | == Method == | ||
| Line 17: | Line 17: | ||
* (Fronts only) Remove Phillips screw from mirror cover and remove mirror cover. It is held in with a fairly strong spring clip at the top: just pull firmly and it'll come. | * (Fronts only) Remove Phillips screw from mirror cover and remove mirror cover. It is held in with a fairly strong spring clip at the top: just pull firmly and it'll come. | ||
| − | * Remove Torx screw ( | + | * Remove Torx screw (T27) from door handle recess. The tool needs to be inserted in the top right part of the plastic cover, and NOT in the position shown in the pic, as this may leave the cover scratched or damaged.. |
| − | * The door pull (the bit you put your fingers in to pull the door shut) is lined with a plastic L-shaped piece (bottom and "fingers-side") which needs to come out. Using a flat blade screwdriver or similar tool in the gap between the top edge of the | + | * The door pull (the bit you put your fingers in to pull the door shut) is lined with a plastic L-shaped piece (bottom and "fingers-side") which needs to come out. Using a flat blade screwdriver or similar tool in the gap between the top right hand edge of the the door trim, carefully but firmly push it away from you to unclip it, then lift it out. This will be much easier if you 'pull' the door release handle into the open position, as it will give the piece more room to pass the handle. |
[[Image:remove-pull-lining.jpg]] | [[Image:remove-pull-lining.jpg]] | ||
Revision as of 16:30, 28 January 2010
Tools required
- Sharp knife
- Wide flat-blade screwdriver or similar tool
- Medium-sized Phillips-head screwdriver (cross-head, No 2 size)
- Torx T27 driver, although most people may only have a T25 driver, which will work, but with a lose fit.
Method
- Remove the circular screw covers on mirror cover (fronts) and door handle recess using a sharp point (knife?). Be very careful not to lose them when they fly out, and take care not to mark the plastic.
Ignore the tweeter in this shot, and you may prefer to use two hands if you're not also holding a camera:
- (Fronts only) Remove Phillips screw from mirror cover and remove mirror cover. It is held in with a fairly strong spring clip at the top: just pull firmly and it'll come.
- Remove Torx screw (T27) from door handle recess. The tool needs to be inserted in the top right part of the plastic cover, and NOT in the position shown in the pic, as this may leave the cover scratched or damaged..
- The door pull (the bit you put your fingers in to pull the door shut) is lined with a plastic L-shaped piece (bottom and "fingers-side") which needs to come out. Using a flat blade screwdriver or similar tool in the gap between the top right hand edge of the the door trim, carefully but firmly push it away from you to unclip it, then lift it out. This will be much easier if you 'pull' the door release handle into the open position, as it will give the piece more room to pass the handle.
- Remove Phillips screws from door pull recess: 2 in front doors, 1 in rears.
- Remove Phillips screws from around the door: 6 on front doors and 4 on rears.
- Remove the door card by lifting it up and out. You'll need to remove the connector from the window switches - there's a locking tag to manipulate to get them to release.
Window switches are clipped in from behind. If you remove them, make sure you get all clips to catch when re-fitting, as it is annoying to have to remove the door panel again when you haven't got one of them in and the switch starts dipping at the unsecured end. Also, don't forget to reconnect the electrical connector before re-fitting the door card.
Your Privacy Choices