Difference between revisions of "Interior Door Handle Illumination"

Revision as of 03:22, 18 September 2008

Imagine the situation - you're courting an attractive young lady, the evening's gone well, and you're dropping her off at home in a dark street. You share a light kiss, she opens the door and she's gone for the night. Later, things develop well, and you marry and raise a family. One of your children goes on to be the chief scientist on the SpaceGuard programme that successfully saves the earth from destruction by an oncoming asteroid. Good news indeed.

But let's rewind to that first evening. Assume that your lady friend cannot find the door handle in the dark. She giggles nervously as she tries to find the handle, feeling awkward and uncomfortable. In an attempt to put her at her ease, you laugh too - but she interprets this as mockery! Things go downhill from here, and you split up; she instead falls for a man with a top-spec Mk2, which already has illuminated handles. Later, everyone dies in a hideous fireball when the earth is struck by an oncoming asteroid.

I think it's clear why this is such a critical modification.

Here's how to get illuminated interior door handles on your Mk3. You can fit this in any door that has electric windows, as it uses the ignition-live feed that illuminates the switches. If you have a facelift LX with manual rear windows, you're on your own. Note that the rear electric window disable switch on the driver's door also disables the illumination on the rear switches, so your handle lights will go out too.

Parts needed per door

• 5mm LED in chosen colour. Choose a fairly bright version.
• Suitable resistor. I used 3x270ohm in series for a red LED. See Calculating LED Resistor Values.
• Wire, either twin or two separate lengths. You'll need about 40cm per door, and you'll need to be able to distinguish the two wires.
• Various bits of heatshrink if you want to do it properly, insulting tape if you can't be bothered.
• Tape for fixing your new wiring to the door.
• Some form of milky white plastic sheet. I used a 4 pint Asda milk bottle, well washed.
• Decent glue. I used SuperGlue (cyanoacrylate).

Tools needed

• Soldering iron and solder. Seriously, don't mess around with twisting and taping.
• Tools for cutting / stripping wire. I prefer to strip insulation by melting the "cut point" with the soldering iron and pulling, as that avoids damage to the already-thin conductors.
• Cross-head (Philips) screwdriver
• T25 Torx driver for the door handle recess screw. You might get lucky with the right-sized flat blade screwdriver, but don't come crying if you strip it.
• 5mm drill bit.
• Some method of cutting a roughly rectangular hole in plastic. I bodged it with multiple 3mm hoels with a drill plus some filing. Neatness is not critical, as the hole won't be seen.

Build LED loom

Before you start taking the car apart, construct the LED loom. Put the series resistor(s) in line with the positive wire. The LED will probably have a flat bit at the base of its plastic case: this shows which leg is the cathode (negative). At the far end of the wire, build a "Y" piece into the end to allow you to connect your new wiring into the cut door wiring.

As above, use plenty of heatshrink. Insulation is very important.

Remove door card

See Removal Of Door Cards - Mk3.

Drill hole

In the plastic door handle surround attached to the door (not the bit on the door card) drill a 5mm hole on the "slope", ideally about 1/3 of the way from the inside edge to the outside edge.

Install wiring

First, identify the switch illumination wires using, for example, the Haynes wiring diagrams (Amazon: pre-facelift / facelift). Look out for the German colour abbreviations: there's a key at the top of the diagrams. In my pre-facelift Graphite, these are:

• Driver's door: Green/Yellow is positive, Black is ground. There are a lot of "black with a stripe" wires, but only one pure black wire.
• ...

Unwrap some of the fabric cable wrap about 6" away from the switch. Separate the wires you need from the bunch, cut and strip them. Tin the ends with solder, then, when cool, fit a bit of unshrunk heatshrink ready to cover the joint when you've made it. Make sure it's waiting far enough away from the end that it doesn't get shrunk when you join the ends!

Tin the ends of your LED loom, and solder in the wiring. Slide the heatshrink over the join, and shrink using heat from the iron. Be sure to not melt any insulation or burn a hole in the door membrane!

Fit LED

Once you have the LED loom wired in, make sure it illuminates when you turn the ignition on.

Push the LED into the hole, taking care not to bend the leads too much. Ideally, the hole will be tight enough for a push-fit, but if it isn't, use a suitable glue or putty to secure it.

Then secure the wiring to the door membrane using suitable tape. Try to ensure that the LED's leads are not under tension or free to vibrate, which may lead to fatigue failure.

Cut window in handle cup

With the door card still off, and the LED fitted, install the handle trim "cup" into position. Check alignment with the Torx screw hole.

Turn the LED on (ignition) and note the area on the top of the cup that it illuminates. Switch off again and remove the cup.

Using whatever means you have, cut a suitable hole in the cup to allow the light through. It doesn't need to be neat as it'll be covered up, but if drilling, take care not to damage the other visible plastic surfaces in the cup.

Reinstall the cup to check that the hole is in the correct place: all of the LED's beam should go through it. Remove the cup, and enlarge the hole further if necessary.

Cut a flat piece of milky white plastic (milk bottles are good) to be stuck to the inside of the cup to cover the hole. Leave enough around the edge to glue it to the plastic surrounding the hole. Glue it on, observing the usual safety precautions for the adhesive you choose. Leave to dry.

Reassemble

Refit the door card. Don't forget to connect the window switch! Insert your modified cup and try it out!

If, after testing, you decide the light is too bright, you can dim it down by removing the cup and gluing another layer of plastic in the hole. There's no need to remove the door card to make this adjustment.